Jump to content
Model_Monkey

Model Monkey at Chattanooga, and early Spitfire and Hurricane Merlin engine "orange slice" exhausts.

Recommended Posts

Posted (edited)

Going to be at the IPMS Nationals at Chattanooga? 

Please stop by the Toms Modelworks booth, say "hi" to Richard Harden, and see a selection of Model Monkey 3D-printed products. Yes, you can buy them from Richard! 

Safe travels! 

Model Monkey Catalog of over 2000 products for scale modelers.

 

file.php?id=119115&mode=view

 

file.php?id=119114&mode=view

 

file.php?id=119116&mode=view

Edited by Model_Monkey
Updated.

Share this post


Link to post
Share on other sites
Posted (edited)

How did I miss that?  And yes, Richard of Toms Modelworks will have a few on hand in Chattanooga at the Toms Modelworks booth.

 

Well here you go, in 1/24 and 1/32 scales, Model Monkey is pleased to announce hollow Merlin engine exhausts for Spitfires, Seafires, Hurricanes and Sea Hurricanes have been added to the catalog. The exhausts are early Merlin engine "orange slice"-type, appropriate for Spitfire Mk. I, Mk.II, Mk.V and Mk.VI; Seafire Mk.Ib; and Hurricanes and Sea Hurricanes Mk. I, Mk. II and Mk.XII. The exhausts are 3D-printed in gray resin. 

 

Also available at Chattanooga, and online, are K-14 / Mk.18 gunsights for P-51, P-47, F6F and F4U aircraft, in 1/24 and 1/32 scales.  Photos below.

 

file.php?id=118924&mode=view

 

file.php?id=118925&mode=view

 

file.php?id=118926&mode=view

 

file.php?id=118927&mode=view

 

 

 

file.php?id=118929&mode=view

 

file.php?id=118930&mode=view

 

file.php?id=118931&mode=view

 

file.php?id=118932&mode=view

 

file.php?id=118933&mode=view

Edited by Model_Monkey
Clarity.

Share this post


Link to post
Share on other sites

Thanks, Ray!

 

To be released later this month:

 

- 1/24 and 1/32 scale N-9 gunsights for P-51, P-47, etc. (two different types) 

- 1/32 scale Beaufighter torpedo for Revell

- 1/24 P-51D/K (Mustang Mk.IV) landing gear wells for the classic Airfix kit

- 1/28 scale "Spandau" LMG 08/15 machinegun for Revell Fokker Dr.I and Fokker D.VII

 

To be released in September:

 

- 1/32 scale Beaufighter observer's station for Revell

- 1/28 scale Oberursel Ur.II motor for Revell Fokker Dr.I

- 1/28 scale Le Rhône 9J Motor for Revell Sopwith Camel

- 1/28 scale Le Rhône 9C Motor for Revell Sopwith Camel

Share this post


Link to post
Share on other sites
47 minutes ago, Model_Monkey said:

To be released later this month:

- 1/24 and 1/32 scale N-9 gunsights for P-51, P-47, etc. (two different types) 

- 1/24 P-51D/K (Mustang Mk.IV) landing gear wells for the classic Airfix kit

 

To be released in September:

- 1/32 scale Beaufighter observer's station for Revell

Well, there's two months of my meager modeling budget spoken for... ;) 

 

Can't wait! :) 

 

D

Share this post


Link to post
Share on other sites

Looking forward to seeing your 1/24 Mustang wheel wells!

 

That will save hours of work and fiddling for anyone building that classic but still very worthwhile kit. I've already started preparing another build in anticipation of purchasing all your Mustang parts.

 

Thanks so much!

 

Richard

Share this post


Link to post
Share on other sites

Might we see a set of 32nd Spitfire fishtails slipped in as a surprise...:whistle:  I have some aftermarket ones and they are all varying sizes, it is so frustrating.  It's to go in my Tamiya MkIX to MkVc conversion.  The opening is the same for early and late engines.  I should start a build thread as I have made many of the changes already including the wings.

 

However this 24th Mustang stuff has me wondering about a future build...… Might look good next to my Postwar Mosquito:hmmm:.  Need to check what else is out there to help this (me) kit out.

 

Might have to re-read your Mustang project again Richard!

 

Cheers guys

Anthony

 

 

Share this post


Link to post
Share on other sites
2 hours ago, Anthony in NZ said:

 

However this 24th Mustang stuff has me wondering about a future build...… Might look good next to my Postwar Mosquito:hmmm:.  Need to check what else is out there to help this (me) kit out.

 

Might have to re-read your Mustang project again Richard!

 

Cheers guys

Anthony

 

 

 

Have to agree that a RNZAF Mustang would look fabulous beside the Mosquito...:ph34r:

 

Having seen your jaw-dropping Mosquito detail work, the Mustang would be much easier...plus it has only one engine. :D All the ModelMonkey parts would save many hours of work and frustration...seriously. 

 

I should get a commission for pushing these Mustang parts lol.

 

Finish that Mosquito first though. 

 

Richard

Share this post


Link to post
Share on other sites

LOL, you should! Well once I have this 48th Mosquito kit out the way for the fund raising for the Mosquito restoration I can crack on again with the 24th one!

 

Thanks for your compliments on my Mosquito, big praise indeed coming from you

 

Thank goodness we have companies like Modelmonkey there to help us out 

 

Cheers

Anthony

 

Share this post


Link to post
Share on other sites

  • Recently Browsing   0 members

    No registered users viewing this page.

×
×
  • Create New...