SCRATCH BUILDER Posted September 28, 2018 Author Share Posted September 28, 2018 (edited) I have taken a long hard look at that Ben, for $500.00 i don't think you can go wrong, should bet great for all the little bits. Edited September 28, 2018 by SCRATCH BUILDER Link to comment Share on other sites More sharing options...
SCRATCH BUILDER Posted December 14, 2018 Author Share Posted December 14, 2018 AnyCubic users, Might be a helpful tip, Been using a plastic polish to clean my FEP when it gets clouded and extend its life. brahman104 1 Link to comment Share on other sites More sharing options...
AlexM Posted January 14, 2019 Share Posted January 14, 2019 Hi there, I want to share some experience with my Anycubic Photon 3d printer. I read some positive comments about the Phrozen ABS like grey resin. I gave it a try, and made a radial engine. Here, the various cylinders are sticking on the print plate, still covered with liquid resin. They all sit on support struts, which can be easily removed after printing. After cleaning in Isopropyl alcohol, that’s how it turned out. The whole diameter of the engine is about 4 cm. Looks promising for a 400 € printer Cheers Alex LSP_Kevin, Tnarg, D.B. Andrus and 6 others 9 Link to comment Share on other sites More sharing options...
SCRATCH BUILDER Posted January 15, 2019 Author Share Posted January 15, 2019 Nice Alex, I made some 1/16 scale servos for my V1 project. what settings are you using for the Phrozen ABS like grey resin 7 minutes ago, Jennings Heilig said: Just to make it easier to paint/finish?? Hey Jennings, Thats correct, FDM printer/Resin printer it's all the same, Alex would have had to put in support structure if he printed as one piece, he would have to support all the overhanging material and it would have been way to hard to clean up AlexM 1 Link to comment Share on other sites More sharing options...
ghatherly Posted January 15, 2019 Share Posted January 15, 2019 20 hours ago, AlexM said: Hi there, I want to share some experience with my Anycubic Photon 3d printer. I read some positive comments about the Phrozen ABS like grey resin. I gave it a try, and made a radial engine. Here, the various cylinders are sticking on the print plate, still covered with liquid resin. They all sit on support struts, which can be easily removed after printing. After cleaning in Isopropyl alcohol, that’s how it turned out. The whole diameter of the engine is about 4 cm. Looks promising for a 400 € printer Cheers Alex IN the pictures no layer lines are showing. Have you worked any of these parts to remove them or is this printer producing completely smooth parts? thx Gary AlexM and Out2gtcha 2 Link to comment Share on other sites More sharing options...
Out2gtcha Posted January 15, 2019 Share Posted January 15, 2019 Wow, those parts look really clean and very nice, especially for 3D printed parts. 3 minutes ago, ghatherly said: Have you worked any of these parts to remove them or is this printer producing completely smooth parts? I would like to know that as well.................usually parts made on home printing 3D printers, the "stepping" is very noticeable, even in 3D printed parts that came in my 1/32nd Extra 330. These dont appear to have any of that. AlexM 1 Link to comment Share on other sites More sharing options...
BiggTim Posted January 15, 2019 Share Posted January 15, 2019 Agreed. I think this year might be the year I pull the trigger on one of these. I'm learning the modeling software now, should be up to speed in a few months, so maybe this summer. Tim Out2gtcha, Ryan and AlexM 3 Link to comment Share on other sites More sharing options...
Out2gtcha Posted January 15, 2019 Share Posted January 15, 2019 12 minutes ago, BiggTim said: I'm learning the modeling software now, should be up to speed in a few months, so maybe this summer. Thats my issue, is what program to get and learn to make stuff on the 3D printers. BiggTim 1 Link to comment Share on other sites More sharing options...
BiggTim Posted January 15, 2019 Share Posted January 15, 2019 1 minute ago, Out2gtcha said: Thats my issue, is what program to get and learn to make stuff on the 3D printers. I chose Fusion 360, as I work with Autodesk software a lot, and there are some similarities in design. I believe Steve (Model Monkey) uses it, and likes it. Plus, they have a free "startup" license that is open-ended for people who just use it for their own purposes or for small run stuff to sell, up to 100k a year, I think. If I made that much, I'd happily pay for it. There are lots of fantastic tutorials on Youtube. Tim Out2gtcha 1 Link to comment Share on other sites More sharing options...
Out2gtcha Posted January 15, 2019 Share Posted January 15, 2019 Just now, BiggTim said: I chose Fusion 360, as I work with Autodesk software a lot, and there are some similarities in design. I believe Steve (Model Monkey) uses it, and likes it. Plus, they have a free "startup" license that is open-ended for people who just use it for their own purposes or for small run stuff to sell, up to 100k a year, I think. If I made that much, I'd happily pay for it. There are lots of fantastic tutorials on Youtube. Good to know! I know there are a LOT of programs out there , and its tough to know which one to get as its quite a commitment (as you already know!) once you decide on which program to start to learn. Im going to try to save up for one this year myself, as I genuinely think this is the way of the future for the hobby, and could open up whole new avenues for us, not available in the past. AlexM and BiggTim 2 Link to comment Share on other sites More sharing options...
SCRATCH BUILDER Posted January 15, 2019 Author Share Posted January 15, 2019 2 hours ago, ghatherly said: IN the pictures no layer lines are showing. Have you worked any of these parts to remove them or is this printer producing completely smooth parts? thx Gary I'm sure there would be some on the hub but there so small and i mean small that primer will blend them. And the orientation the he printed the cylinder heads at there would be no print lines ( printed at .05mm ) 1 hour ago, BiggTim said: Agreed. I think this year might be the year I pull the trigger on one of these. I'm learning the modeling software now, should be up to speed in a few months, so maybe this summer. Tim I recommend the ANYCUBIC, a few of us have it and for $500.00 its your best bet to get started, I have had mine 3 months now and not a failed print (you do have to level it correctly). there resin is cheaper, but it is open source so you could use any resin you want. I post some pictures here of my prints. AlexM, BiggTim and Out2gtcha 3 Link to comment Share on other sites More sharing options...
BiggTim Posted January 15, 2019 Share Posted January 15, 2019 22 minutes ago, SCRATCH BUILDER said: I recommend the ANYCUBIC, a few of us have it and for $500.00 its your best bet to get started, I have had mine 3 months now and not a failed print (you do have to level it correctly). there resin is cheaper, but it is open source so you could use any resin you want. I post some pictures here of my prints. Yes, that is exactly what I am planning to get! Your experiences here as well as some other sources have convinced me that this is the best route for the type of things I want to do. I'm looking forward to it, but I have to save up.... Out2gtcha and SCRATCH BUILDER 2 Link to comment Share on other sites More sharing options...
AlexM Posted January 15, 2019 Share Posted January 15, 2019 15 hours ago, Jennings Heilig said: Pardon my noob question - if you were going to 3D print a radial engine, why wouldn’t you print the whole engine as one piece instead of a bunch of parts you have to assemble? Just to make it easier to paint/finish?? As Rick (SCRATCH BUILDER) said, somehow you have to outsmart gravity. Actually you can print at a certain overhanging angele, and even some vertical areas without support below. But to longer the distance, the higher the risk of a failed print. For example, if this engine would be printed as one part, the thin pushrods (0,7 mm diameter) would lay pretty flat "in the air", only connected to the main engine at both ends. I havent tried yet, but I suppose such a print wouldn't look great. You could add support-structure under those areas in the printing software, but it would be a pain to remove the support after printing. And as you said, it propably makes painting easier BiggTim and SCRATCH BUILDER 2 Link to comment Share on other sites More sharing options...
AlexM Posted January 15, 2019 Share Posted January 15, 2019 15 hours ago, SCRATCH BUILDER said: Nice Alex, I made some 1/16 scale servos for my V1 project. what settings are you using for the Phrozen ABS like grey resin Hi Rick, thanks! My settings are: Normal exposure time (s): 16 Off time (s): 0 Bottom exposre time (s) 90 Bottom layers: 8 I haven't tried if other settings would lead to reasonable results in shorter time, but with those settings, my printed parts with this resin turned out nice so far. And for me as a hobbyist, time isn't really a critical factor. But even with those settings, the prints go pretty fast. One batch of cylinder takes just a bit more than two hours. Here is a overview with recommended settings from other Anycubic users: https://docs.google.com/spreadsheets/d/1crvzMnt_8NJXAsABinoIhcOjE8l3h7s0L82Zlh1vkL8/edit#gid=0 BiggTim 1 Link to comment Share on other sites More sharing options...
AlexM Posted January 15, 2019 Share Posted January 15, 2019 4 hours ago, ghatherly said: IN the pictures no layer lines are showing. Have you worked any of these parts to remove them or is this printer producing completely smooth parts? thx Gary Hi Gary, in fact, I haven't done any post processing concerning the surface. I just removed the bottom support structures, and washed the parts in isopropyl alcohol. Finally the parts layed a few minutes under a uv lamp to harden the parts more. The parts were printed with a layer hight of 0,04 mm. Cheers Alex BiggTim and Out2gtcha 1 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now