Nachtjaeger Posted June 12, 2015 Share Posted June 12, 2015 What is being used these days to simulate ignition wires on radial engines? What type and what gauge wiring do you guys use? I've been told to use soldering wire, telephone wire (who's has a phone with a cord these days...) small diameter lead wire. What do you guys use? Link to comment Share on other sites More sharing options...
Bill_S Posted June 12, 2015 Share Posted June 12, 2015 I've used wrapping wire in the past. 30 AWG. 0.019" diameter with the insulation, 0.009" diameter for the bare wire. If you have a good craft store nearby, I'd recommend beading wire. It's available in a variety of diameters. Just be sure to get solid, not stranded. Link to comment Share on other sites More sharing options...
dodgem37 Posted June 12, 2015 Share Posted June 12, 2015 I use wire. 36 gage. You can see it in the second post in the Fock Wulf thread in my signature. And .005 mono filament. From Dick's Sporting Goods. I don't have any imagery of my using mono-filament on an engine. But in post 340 on page 23 of the Mustang thread in my signature you'll be able to see it in use as engine compartment wiring. Sincerely, Mark Link to comment Share on other sites More sharing options...
Out2gtcha Posted June 12, 2015 Share Posted June 12, 2015 As you are in the states, I purchased a "lead wire assortment" from BassPro shops HERE that has proved most valuable for running ignition wires, cockpit wires, as well as all sorts of MLG bay wiring. It has a six-compartment box, one for each of the sizes, which range from .010, .015, .020, .025, .030 and .035. Zero77 and NORMCO 2 Link to comment Share on other sites More sharing options...
Out2gtcha Posted June 12, 2015 Share Posted June 12, 2015 IMHO the thin lead stuff works best for me, as it takes curves well, and is always inclined to stay exactly where you put it, in the exact shape you put it in. The only cons are it is easily smashed, or crushed if you man-handle it. Link to comment Share on other sites More sharing options...
Mal_Belford Posted June 26, 2015 Share Posted June 26, 2015 I use Fishing line, copper wire from a cord or nic cable, and lead wire. Depends what kind of work and look im after. /Mal Link to comment Share on other sites More sharing options...
Nachtjaeger Posted July 6, 2015 Author Share Posted July 6, 2015 Thanks for the info guys, like always this is the place for great advice and modelling tips. I will try some of these materials in my builds. Link to comment Share on other sites More sharing options...
Zero77 Posted July 6, 2015 Share Posted July 6, 2015 For the wire, i use lead wire used for fly fishing (to ballast the lures). They are sold in reel, there are several diameters, they are pretty cheap and will last a long time. Thin copper wires will do it as well, but i prefer the lead wires as they are softer and i have a larger range of diameters. Then, i drill small holes on the engine, put a small bit of micro-tube (about 0.5mm diam) inside and i have a set of spark plugs. Then i just have to put the lead wires inside. On the other side, on the ignition ring, it just depends of how the kit is made. I can make small holes on the small cylinders of the ring, or just glue the wires behind the ring if they are too small to be drilled. Link to comment Share on other sites More sharing options...
Marmaduke Posted September 13, 2015 Share Posted September 13, 2015 I most often used copper wires of varying sizes from different electrical cords. I like to anneal it before using it which has a twofold effect. First it makes it more pliable and easier to work with and second it gives it an old used look like natural weathering. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now