Search the Community
Showing results for tags 'f-117'.
Found 4 results
Guys, i'm back! This time not with something in 1/48 or smaller. That thing... It's the Trumpeter kit, my second 1/32 scale model, and it's quite huge It's so ever slightly bigger than the F-15 in lenght and even in wingspan, which impressed me a bit. Alright, let's do it. I plan a rather slow and longer build. Some may know very well the quality and what's in the box, but i'm gonna make a thorough review these days whatsoever. Here is just a quick glimpse: And of course, i'll take advantage of the AFV Club's tinted canopy, cause i think it's absolutely necessary for a good looking F-117. I cannot tint such a huge canopy by myself and not leave any trace of dust, etc. In 1/48 or less - it's ok because the little imperfections are almost invisible, but this one is one, enormous and two, with perfectly flat straight sides. I'll also use the GTR Wheel set that i didn't use in my F-15E. The kit tires are from very hard rubber and quite small in size. I have the original dimensions of the plane's tires and did the quick measurements. The GTR tyres are perfect. Only the front tyre is a bit smaller in diameter so i might still use the kit's rubber tyre for the nose wheel. And on the other hand, i know that the F-117 had just about the same avionics as the F-18 and just about the same landing gear as the F-15, so that's the perfect moment to use the gorgeous GTR tyres and wheels. And finally, the extra PE screen for the FLIR and DLIR. This is obligatory as well, because the provisions for these sensors are huge. I did a little mistake though by getting the 4x6 screen mesh in believing that the holes are rombs. Yeah, they are rectangulars... i couldn't notice that on the photos and this is my firt time using such a PE screen. Nevertheless, i think i can place the screen at an angle so they can look as rombs. I plan to start from the landing gear and make everything moveable again, for "2 models in 1" - in a parked and in-flight mode. The canopy, the gear, all the control surfaces and the bomb bays will close/open. As for the airframe - i have no idea yeat, but i think it will be one of the early Nighthawks, something Desert Storm-related in a full stealth mode with all the lights and antennas retracted and without the two RCS enhancers on the sides. Quite weathered as well. I'm only looking for a pilot figure and if i cannot find any, i plan to get the F-16 resin figure+seat set by Aires. But i'll wait on that one yet. Nighthawk!
A lot of time passed since my last post here, I promise I'll try to be more active. Since my MiG-23, I finished 4 birds, I'll present one of them here, next will post in a few days. My Nighthawk was made almost Out of the box, I've changed only wheels for Eduard ones. Base was inspired by last flight box by Academy. Biggest problem was with exhaust painting, I did some research, but it is so hard to find a decent photos, so it is my vision of exhaust. Watch and comment - and please, be gentle. . . . . . . . . . . . . . . . . .
It begins. After a nearly 2 decade search for the right kit, and several attempts in 1/48 with the Tamiya kit, I believe I've finally found the plastic of my dreams. The Trumpeter kit corrects the myriad flaws of the old Testors, and offers a better working scale for what I hope to accomplish in 1/32 than the Tamiya did a step smaller. Life and work force me to be a very part time modeler, but I will post progress here - slow as it may be. As mentioned, the basis for this build is the new-ish Night Hawk kit. Having been to market for a little over a year, there are several nice aftermarket options now available. While I haven't made a final decision on what I would like to include, the cockpit, seat and gear/wheels are about the only real areas of detail on this kit - so I figured they're as good a place as any to get started. Que Quickboot Aces II replacement seat, and an Eduard Brassin wheel set. Both are excellent quality, and offer a substantial improvement in detail to the kit parts. As several of you are aware, I'm working on several aspects of this kit to improve upon the plastic or photo etch options that currently just don't quite cut it. One of these details are the engine intake grids. My hope is to find a willing engineer with access to a micro machining unit that will be able to help create as close to an exact scale replica of the grids as possible. Failing that....well, I'll cross that bridge if/when I get to it. In the mean time, I'll be collecting paints, glue, and all the other sundries I've since parted with over the years since my last attempt at this silly project. Thanks once again to all the help I've received so far in looking for information to help me along. I'll be sure to update as progress is made. Brian~
Following on from Uilleans excellent thread , and having seen a few other impressive builds online, I thought I would splash out and have a go at the "Wobblin Goblin" myself. Back in 1990 I remember watching the F-117 and the strike damage being broadcast on TV to the world, during the first Gulf War. The aircraft is a source of fascination for me considering getting the unusual shape to fly as well as the technology to make it stealthy and virtually invisible to enemy radar defences. So time to gather some references and decide on what after-market items to add to the kit. http://lh4.googleusercontent.com/-gTvCde6KOFo/UzMTz-4Z8SI/AAAAAAAASsc/CYc-0Pk2yWI/s1024-no/IMAGE_668.jpg The Squadron/Signal Walk Around Number 26 is very good, and probably the best reference for the modeller that I have seen. The Pilot's Flight Operations Instructions are less useful but of interest to anyone interested in the checklists and general operation of the aircraft. There are no photos in this volume and only a few line drawings of the cockpit and a few scrap drawings of wheel bay equipment. Half of the manual consists of performance graphs. Additionally I purchased the excellent Eduard Brassin Resin wheels set, with accurate tyre treads and wheel spokes for later production aircraft. I also purchased the Eduard, Weapons bay detailing set, the Cockpit interior and exterior detailing set for the various mesh grilles that cover the various exhaust ports on the fuselage. I don't intend to reiterate anything that Uillean has already said on his build, but will post some progress shots, and try to mention any traps or pitfalls with the build as I go along.