Cap'n Wannabe Posted August 29, 2022 Share Posted August 29, 2022 In 2003, the soldiers' seats in the M113 were replaced (I think - may not have got out of prototype stage..) with storage lockers topped by cushions. I believe this to be a uniquely Australian mod....I did the drawings, and I just happen to have a set lying around. I also have a set of drawings for support stands used for maintenance, and a set of the commander's seat from 2004. Let me know if you're interested.. GMK 1 Link to comment Share on other sites More sharing options...
GMK Posted August 29, 2022 Author Share Posted August 29, 2022 12 minutes ago, Cap'n Wannabe said: In 2003, the soldiers' seats in the M113 were replaced (I think - may not have got out of prototype stage..) with storage lockers topped by cushions. I believe this to be a uniquely Australian mod....I did the drawings, and I just happen to have a set lying around. I also have a set of drawings for support stands used for maintenance, and a set of the commander's seat from 2004. Let me know if you're interested.. Thanks, @Cap'n Wannabe - appreciate the offer. I’m modelling my vehicle closed up, otherwise I’ll never finish it. Cheers. Link to comment Share on other sites More sharing options...
GMK Posted August 29, 2022 Author Share Posted August 29, 2022 One thing with slicing models is that the orientation plays an important part in the success or otherwise of the prints. This was one version, with most objects canted 30 degrees or so to the printer bed. Here’s where it started. Version two has them placed vertically. Thanks for looking in. Ryan, Rockie Yarwood, LSP_Kevin and 3 others 6 Link to comment Share on other sites More sharing options...
LSP_Kevin Posted August 30, 2022 Share Posted August 30, 2022 What printer and slicer are you using, Greg? Kev Link to comment Share on other sites More sharing options...
GMK Posted August 30, 2022 Author Share Posted August 30, 2022 19 minutes ago, LSP_Kevin said: What printer and slicer are you using, Greg? Kev G’day Kev, I’m using an Anycubic Photon Mono X printer, Anycubic grey resin, & Anycubic Workspace slicer. Cheers, Greg LSP_Kevin 1 Link to comment Share on other sites More sharing options...
LSP_Kevin Posted August 30, 2022 Share Posted August 30, 2022 4 minutes ago, GMK said: G’day Kev, I’m using an Anycubic Photon Mono X printer, Anycubic grey resin, & Anycubic Workspace slicer. Cheers, Greg Nice! Looks like it's working well for you. Kev GMK 1 Link to comment Share on other sites More sharing options...
jeroen_R90S Posted August 31, 2022 Share Posted August 31, 2022 Really inspiring stuff, I just wish I had more spare time to try learining Fusion 360 or something. My oldest wants a 3D printer for his birthday, I'm thinking of giving him one my older PC's with Fusion 360 instead! Inspiring stuff for sure GMK 1 Link to comment Share on other sites More sharing options...
GMK Posted September 6, 2022 Author Share Posted September 6, 2022 On 8/31/2022 at 7:02 PM, jeroen_R90S said: Really inspiring stuff, I just wish I had more spare time to try learining Fusion 360 or something. My oldest wants a 3D printer for his birthday, I'm thinking of giving him one my older PC's with Fusion 360 instead! Inspiring stuff for sure Thanks, Jeroen. Learning CAD is like learning how to fish. Definitely worth the investment of time. I’m experimenting with clear resin for the turret as the translucent green is just too green. One cool thing is that you can see the photo-sensitive resin being cured, layer by layer. Pretty cool! Using 0.01mm layers takes a while, though. Thanks for looking in. Ryan, jeroen_R90S, patricksparks and 1 other 3 1 Link to comment Share on other sites More sharing options...
GMK Posted September 8, 2022 Author Share Posted September 8, 2022 Well, highest resolution print is done The print wasn’t as good as initial impressions, though the turret being translucent made detecting faults trickier. For some reason there’s a fold or wrinkle on the ten o’clock facet of the turret. The parallel lines highlight the fold in the top line of the visiblock, circled in red. Thanks for looking in. Ryan, patricksparks and Rockie Yarwood 3 Link to comment Share on other sites More sharing options...
GMK Posted September 10, 2022 Author Share Posted September 10, 2022 After playing with orientation & layer height, I reckon I’ve got an acceptable turret. This is it being cured. While it was printing, drying, & curing, I drew up the interior & exterior masks for the visiblocks. These were then cut via laser cutter. Test fit on the turret. With luck I’ll be able to prime today. Thanks for looking in. Jeff T and patricksparks 2 Link to comment Share on other sites More sharing options...
GMK Posted September 12, 2022 Author Share Posted September 12, 2022 Mucked about with some paint in an endeavour to get a motivational endorphin high/illusion of progress. I used SMS RAF Sky for the interior sea foam green. Then SMS camouflage brown, camouflage green, camouflage black, & insignia white. Masks for the Charlie Company chevron were laser cut. Thanks for looking in. Rockie Yarwood, Cheetah11, Ryan and 4 others 7 Link to comment Share on other sites More sharing options...
Rockie Yarwood Posted September 13, 2022 Share Posted September 13, 2022 Nice! GMK 1 Link to comment Share on other sites More sharing options...
GMK Posted September 15, 2022 Author Share Posted September 15, 2022 On 9/13/2022 at 1:26 PM, Rockie Yarwood said: Nice! Thanks, Rockie! Now that the new resin printer is dialled in, thought I’d have another bash at the front hull in another material. 450 grams of resin! The gun depression rail looks a bit wonky, but that’s fixable. Hasn't yet been washed & cured yet, but couldn’t resist placing the turret on it. Test fit of the left track shroud. Thanks for looking in. mambodan72, Rockie Yarwood, patricksparks and 4 others 6 1 Link to comment Share on other sites More sharing options...
GMK Posted September 17, 2022 Author Share Posted September 17, 2022 Ran a test print on the rear of the hull. Let’s just say I need to tweak the model. Thought that there could be some issues, but not to that extent. In parallel, the major markings were sketched up. Onto the laser cutter. Looking good. I may redo them with reference cuts to facilitate alignment on the physical model. I need to sort out the tiger’s head, deployment Christmas tree, buoyancy marks, & roadworthy reflective marks, each of which have differing degrees of difficulty. Thanks for looking in. patricksparks and mustang1989 2 Link to comment Share on other sites More sharing options...
Maxim61 Posted September 18, 2022 Share Posted September 18, 2022 2 hours ago, GMK said: Ran a test print on the rear of the hull. Let’s just say I need to tweak the model. Thought that there could be some issues, but not to that extent. In parallel, the major markings were sketched up. Onto the laser cutter. Looking good. I may redo them with reference cuts to facilitate alignment on the physical model. I need to sort out the tiger’s head, deployment Christmas tree, buoyancy marks, & roadworthy reflective marks, each of which have differing degrees of difficulty. Thanks for looking in. I think the rear resin piece needs more supports? GMK 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now