denders Posted July 1, 2020 Author Share Posted July 1, 2020 The PE in the cockpit, is from the Big Ed set. It is not self adhesive though. I used mig Ultra Glue for all the flat surfaces and of course, CA for the small bits. Dave Link to comment Share on other sites More sharing options...
denders Posted July 19, 2020 Author Share Posted July 19, 2020 I had purchased the Avionix gear bay additions and GFM brass landing gear. I'm working on the front gear bay now. Need to detail paint and weathering. AlbertD, mozart, Kagemusha and 12 others 15 Link to comment Share on other sites More sharing options...
denders Posted August 6, 2020 Author Share Posted August 6, 2020 First wing with the Avionix landing gear bay installed. Also the nose gear bay painted up. Greg W, Whitey, johncrow and 11 others 14 Link to comment Share on other sites More sharing options...
CZPetrP Posted August 7, 2020 Share Posted August 7, 2020 Nice work. I wish you a lot of strength... denders 1 Link to comment Share on other sites More sharing options...
chrish Posted August 14, 2020 Share Posted August 14, 2020 Great work going on here! I’ve kinda wanted to build “Bat Bird” after reading Ed Rasimus book “When Thunder Rolled” maybe some day... denders 1 Link to comment Share on other sites More sharing options...
KEi Posted August 18, 2020 Share Posted August 18, 2020 Thanks for the photo, I also had Avionix gear bay which I will use your photo as reference. Your work is superb denders 1 Link to comment Share on other sites More sharing options...
Michael931080 Posted August 18, 2020 Share Posted August 18, 2020 Nice work on the Gear Bay installation! Question, how was it for fit and alignment? denders 1 Link to comment Share on other sites More sharing options...
denders Posted August 19, 2020 Author Share Posted August 19, 2020 11 hours ago, Michael931080 said: Nice work on the Gear Bay installation! Question, how was it for fit and alignment? The main part where the main wheel stows took a bit of sanding of the mold block otherwise its pretty much the way it looks. The sides in the smaller area, upper left, could have been a little longer and perhaps a little taller but then that would also have required more fitting to be done. Link to comment Share on other sites More sharing options...
denders Posted August 23, 2020 Author Share Posted August 23, 2020 More progress, definitely going to make the end date, still lots to go. Working on the resin fin, rudder, nose cone, strake, seams to fill, etc. Might be a challenge in the paint booth too. mozart, Out2gtcha, Isar 30/07 and 15 others 18 Link to comment Share on other sites More sharing options...
chrish Posted August 24, 2020 Share Posted August 24, 2020 looks great...big too! Link to comment Share on other sites More sharing options...
denders Posted August 29, 2020 Author Share Posted August 29, 2020 @LSP_Kevin I noticed this on another thread and I'm not sure if this is the proper procedure. Would you please transfer this to the WIP section. I am not going to be finished in time. Thank you Dave LSP_Kevin 1 Link to comment Share on other sites More sharing options...
denders Posted August 30, 2020 Author Share Posted August 30, 2020 Well, this is probably as far as I'm going to get before the end of the month. Daniel Leduc, Landrotten Highlander, Brett M and 8 others 11 Link to comment Share on other sites More sharing options...
Jack Posted August 30, 2020 Share Posted August 30, 2020 Well, you still have one day, but looking great, very nice build!! Link to comment Share on other sites More sharing options...
BradG Posted August 31, 2020 Share Posted August 31, 2020 Looking good. Your thread can be moved to WIP forum if you like. Link to comment Share on other sites More sharing options...
LSP_Kevin Posted August 31, 2020 Share Posted August 31, 2020 On 8/30/2020 at 2:23 AM, denders said: @LSP_Kevin I noticed this on another thread and I'm not sure if this is the proper procedure. Would you please transfer this to the WIP section. I am not going to be finished in time. Thank you Dave Done! Kev Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now