D.B. Andrus Posted May 18, 2019 Share Posted May 18, 2019 7 hours ago, dodgem37 said: Never fails. Sincerely, Mark That's for sure! Thunnus 1 Link to comment Share on other sites More sharing options...
Thunnus Posted May 18, 2019 Author Share Posted May 18, 2019 Thanks guys! I've sprayed a base coat of zinc chromate into the wheel wells and landing gear covers. These will be given a coat of hairspray before the final color (Insignia White) is applied. My digital camera is acting up. Exposure is wonky and I have to manually set it at +2 or -3 stops to get it from exposing too dark or too bright. And it won't focus like it used to. Definitely something wrong and it just started happening yesterday. I've since given the camera a few hard resets and even updated the firmware but no improvements. I can still get photos out of it but it takes me a lot longer due to the issues. It's a Canon S100 that replaced a Canon S95. I'm monitoring EBay for a used Canon S110 right now. chuck540z3, AlbertD, Gazzas and 6 others 9 Link to comment Share on other sites More sharing options...
Thunnus Posted May 21, 2019 Author Share Posted May 21, 2019 Chipping was HARD! I used the MIG Scratches Effect and I found the AK Real Color Insignia White very stubborn and resistant to chipping. I used the fiberglass brush and also the toothpick. After I chipped the wheel wells, I gave it a gloss coat and applied a dark brown wash. Here's what the wheel wells look like so far with that initial phase of weathering done. It's still gloss so a flat coat and probably some more staining still to come. nmayhew, sandokan, F-4Phanwell and 14 others 17 Link to comment Share on other sites More sharing options...
Guest Vincent Posted May 21, 2019 Share Posted May 21, 2019 Hi This might be because AK real color aren't true acrylic paints and water can't easily reach the hairspray I haven't tried it yet on my Spit but will let you guys know if the same happens to me Vincent Link to comment Share on other sites More sharing options...
Woody V Posted May 21, 2019 Share Posted May 21, 2019 Man, you're killing' it...... beautiful craftsmanship. Back in the 80s I built a tribute model for a Corsair pilot using the old Revel kit and I can't wait to do it again with the Tamiya kit! Thunnus 1 Link to comment Share on other sites More sharing options...
Thunnus Posted May 21, 2019 Author Share Posted May 21, 2019 6 hours ago, Vincent/MDC said: Hi This might be because AK real color aren't true acrylic paints and water can't easily reach the hairspray I haven't tried it yet on my Spit but will let you guys know if the same happens to me Vincent Perhaps! Aren't Tamiya and Mr Hobby Aqueous similar in composition, being acrylic lacquers? In other respects, the AK Real Color paints have been behaving very similar to Tamiya and Mr Hobby Aqueous. Please let us know how the chipping goes on your beautiful Spitfire build. 4 hours ago, Archer Fine Transfers said: Man, you're killing' it...... beautiful craftsmanship. Back in the 80s I built a tribute model for a Corsair pilot using the old Revel kit and I can't wait to do it again with the Tamiya kit! Thank you! You'll have a blast building the Tamiya kit... it really is a modeling marvel. Link to comment Share on other sites More sharing options...
zaxos345 Posted May 21, 2019 Share Posted May 21, 2019 (edited) John, i have tested the real colors a bit myself and they seem to me leaning towards more to mr. paint colors, than to tamiya or Mr. hobby Aqueous. I really love your work!!!!!! John Edited May 21, 2019 by zaxos345 D.B. Andrus and Thunnus 1 1 Link to comment Share on other sites More sharing options...
Durangokid Posted May 21, 2019 Share Posted May 21, 2019 The chipping may have been difficult but it looks fantastic! You really do a nice job making it look totally realistic... Bryan Thunnus 1 Link to comment Share on other sites More sharing options...
brahman104 Posted May 22, 2019 Share Posted May 22, 2019 Absolutely stunning paintwork and building you're doing here. I love what you did with the instrument panel too. I'm keeping a note of that for when I do mine...... Craig Thunnus 1 Link to comment Share on other sites More sharing options...
Thunnus Posted May 22, 2019 Author Share Posted May 22, 2019 Thanks for the positive comments! They really challenge me to not only move forward on these builds but inspire me to try and do better. I've finally gotten to the point where I could install the wires to the landing gear door actuators from the central hydraulic junction. To make this manageable, I cut the actuating struts from the doors and installed them first. I didn't think I could've managed the wiring with the doors in the way. I think this was a good decision as wiring was fiddly enough with the landing gear wells still separate from the wing bottom. The wheels wells have been given a flat coat and I've added some sponge chipping and enamel washes to add some color. The main wheel wells were the last of the four major interior components that needed to be completed (cockpit, engine and tail wheel well being the others). I think the build will move a little faster now. StefanGebhardt, TorbenD, Kaeone57 and 12 others 15 Link to comment Share on other sites More sharing options...
misha71 Posted May 22, 2019 Share Posted May 22, 2019 looks great Thunnus 1 Link to comment Share on other sites More sharing options...
joker Posted May 22, 2019 Share Posted May 22, 2019 Just found this, really a stunning build...I have already built one myself as a Royal Navy aircraft...wish this build had been around when I had done mine, wonderful technique and skill sets. Excellent workmanship. Peter Thunnus 1 Link to comment Share on other sites More sharing options...
Dan Paxton Posted May 22, 2019 Share Posted May 22, 2019 Magnificent build so far sir, thank you for taking us on this journey with you.....I ALWAYS learn from you masters..... Thunnus 1 Link to comment Share on other sites More sharing options...
Gisbod Posted May 22, 2019 Share Posted May 22, 2019 Looks stunning John. Re chipping I’ve had the same issues with MRP - acrylic but with a lacquer twist. Guy Thunnus 1 Link to comment Share on other sites More sharing options...
Kaeone57 Posted May 23, 2019 Share Posted May 23, 2019 (edited) 17 hours ago, Thunnus said: Thanks for the positive comments! They really challenge me to not only move forward on these builds but inspire me to try and do better. I've finally gotten to the point where I could install the wires to the landing gear door actuators from the central hydraulic junction. To make this manageable, I cut the actuating struts from the doors and installed them first. I didn't think I could've managed the wiring with the doors in the way. I think this was a good decision as wiring was fiddly enough with the landing gear wells still separate from the wing bottom. The wheels wells have been given a flat coat and I've added some sponge chipping and enamel washes to add some color. The main wheel wells were the last of the four major interior components that needed to be completed (cockpit, engine and tail wheel well being the others). I think the build will move a little faster now. John, Been busy working so haven't really had a chance to check out your 17740 build. She's looking Great! Hope I'm not to late on this little bit of info for your build, but the 2 "thumbnail" shaped items on the inner most walls of the wheelbays are zippered, canvas inspection covers and not a metal that would chip. Also in the center of the rear most wall is a wooden wedge shaped block which is to aid in stopping the rotation of the tire in the wheel bay and it would probly have rub marks towards center as the tire rubbed it before the rotation stoped. GREAT WORK STILL!!! My apologies for being tardy again!! Alfonso Edited May 23, 2019 by Kaeone57 D.B. Andrus, Gazzas and Thunnus 3 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now