Jump to content
tomprobert

1/48th Boeing B-52H Stratofortress

Recommended Posts

A little more progress to update you on this evening...

 

I've been busy making the individual ribs for the wings - each one has been made from plastic card and then glued to the inner wing surfaces. Making each one identical was tedious to say the least, but the effect is what I was after. I've also been adding some Evergreen stiffeners too, and I'll now need to make the stringers that sit between the ribs and add those. Plenty to keep me busy over the next few sessions!

 

49224088463_b40246b053_z.jpgIMG_1702 by Thomas Probert, on Flickr

 

49224088143_7c27aee9c7_z.jpgIMG_1699 by Thomas Probert, on Flickr

 

Until next time,

Tom

Share this post


Link to post
Share on other sites

Bearing stable doors and bolted horses in mind, for manufacturing multiple identical pieces like your wing ribs, I would cut overlong strips of roughly the correct dimensions and form them into a flat, aligned bundle. Then apply a spot of thin cement at one end to bond them loosely together, taking care not to flood them into an unholy mass.

Just enough to tack the excess ends together, so they can flick apart like leafing through pages in a book.

You can then draw your template on the outer one and carve and sand away everything that's 'not rib'. When done, cut to length and they should all be reasonably identical.

 

Nice job though, doing it the hard one-at-a-time way!

Edited by Chek

Share this post


Link to post
Share on other sites

Here's the result of about 10 hours work on the wing/flap structure so far:

 

49247580053_a392b9a542_z.jpgIMG_E1705 by Thomas Probert, on Flickr

 

49248252907_933f252948_z.jpgIMG_E1706 by Thomas Probert, on Flickr

 

Both inner sections are now more or less complete, with the outer sections to be tackled next. I may well give @Chek's method a go...

 

Tom

Share this post


Link to post
Share on other sites

Very neat work on those flap housings Tom. A mirror base will be a must so they can be seen.

 

One thing I neglected to mention about my multi-method, is to use a clamp along he bottom edge to hold the bundle together.

I used a large Bulldog clip spring clamp the last time I indulged, but no doubt better more sophisticated solutions exist.

Share this post


Link to post
Share on other sites

Afternoon folks...

 

The flap aperture detailing has progressed well - the main structure is now done, with the exception of the flap motors that'll need making and adding later on:

 

49264662622_965cc6f8bf_z.jpgDSC_0292 by Thomas Probert, on Flickr

 

49264470141_04f844c97d_z.jpgDSC_0294 by Thomas Probert, on Flickr

 

49264661702_24224b6e59_z.jpgDSC_0296 by Thomas Probert, on Flickr

 

49264003433_14893ca6a2_z.jpgDSC_0298 by Thomas Probert, on Flickr

 

When the final detailing has been done, these ares will be given a good spraying of zinc chromate - but that won't happen until the model is ready for painting.

 

In other news, I've finished adding the veins to the spoilers on the wings:

 

49264660792_50943257f0_z.jpgDSC_0300 by Thomas Probert, on Flickr

 

And these are the beautiful 3D printed wheels that a friend kindly did for me:

 

49264660322_81010d1c13_z.jpgDSC_0302 by Thomas Probert, on Flickr

 

49264471476_e27fa2f040_z.jpgDSC_0304 by Thomas Probert, on Flickr

 

Unfortunately the colour of the plastic means a lot of the details are lost to the camera, but believe me they're stunning!

 

Now, better get the table cleared for dinner...

 

49264005073_43495e9134_z.jpgDSC_0290 by Thomas Probert, on Flickr

 

Happy modelling folks, and all the best for the festivities!

 

Tom

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

×
×
  • Create New...