Jump to content
Haggis

Post Apocalyptic OV-10A Bronco

Recommended Posts

Photobucket is back, we are saved!

The cockpit was finally finished.  To be honest I just let the imagination run away and I just kept adding more and more so in the end it looks really very busy.  Its all plastic card, bits of that 1:48 F-14 and 1:35 WMIK, lead wire, brass wire and Albion Alloys tubing.

P1320346_zpsljrrnvsh.jpg

P1320371_zpsauwkokaq.jpg

P1320362_zpsfaetzxjb.jpg


That row of black dots are HGW rivets, decals in fact!  Note also the home made spring in the pilot's seat, inspired by the real thing but I think that's part of the comms.  I did this because I think it looked cool!

P1320376_zpsr20jpvxr.jpg

To glue the brass rod, I squashed the ends to give a larger surface area for gluing.

P1320419_zpsfvom355b.jpg

Here is the finished gunner's cockpit.  That seat is from the WMIK!

P1320415_zpsw5h4iv7w.jpg

The pilot's office wasn't neglected.  As well as plastic strip and Albion Alloys tubing, I also added a WMIK thingamajig and some Airscale photo etch bits.
P1320422_zpsbhcgfqfc.jpg

Share this post


Link to post
Share on other sites

Now time for paint, first up, Alclad black primer.  This is highly recommended owing to all the different materials, plus it will help with shading.

P1320430_zps721ylxlc.jpg

Next up was a layer of undercoat of a weathered steel colour; namely a mix of black, buff, red and Medium Sea Grey.  On top was a layer of Ammo of Mig's Scratch Effects chipping fluid.  When dry I sprayed the top coat, Tamiya XF-4 Yellow/Green which is a great Zinc Chromate primer colour.  Note the subtle shading from the undercoat.

P1320459_zpsf3avqu4q.jpg

P1320462_zpsnqoqmkzm.jpg

Now the fun part.  Keeping the area wet I scrubbed the areas of wear with a brush, eventually the water will soak through and dissolve the chipping fluid (you can use hairspray but its a bit of a sledgehammer and can be unpredictable) and lift off the dry paint in realistic chipping patterns.

P1320472_zpsi6thstcx.jpg

P1320448_zpsh5xlbxp7.jpg

Next was the pin wash.  I used a mix of tones from Ammo of Mig's Panel Line Wash (PLW) series and a new product from Alclad called Hogwash (brilliant by the way).  I recieved a sample to test out so I'm not sure where you can get it, if it's even released yet.

The wash was dabbed into the area then when dry removed with a soft moist brush.

P1320492_zpsp4hr96qj.jpg

Time for some detail painting.  The switches were picked out with a fine brush and acrylic paint.  I "wet" dry-brushed the rear CB panel, the detail was too small to accurately paint and dry brushing is not opaque enough and would affect the edges of the box.  By just removing the worst of the excess of the brush you get a much stronger finish.

P1320478_zps5h3gcnio.jpg
P1320491_zpsnz4yr7ny.jpg

If stencils give you nightmares then look away now.  Using Airscale's superb placard decals I dressed up the cockpit, the CB panel has over 40 decals on it alone!  I also added some wiring looms, these are cotton covered wire from Little Cars.

P1320501_zpsekgbjhuj.jpg

The instrument panel was a mix of Airscale decals and kit supplied decal chopped up.  Note I got the Turn and Slip upside-down!

P1320512_zpsfvnsr6ig.jpg


 

Share this post


Link to post
Share on other sites

I wanted to portray a dirty and dusty environment so Ammo of Mig's Airfield Dust and Earth pigments were applied in the nooks and crannies.  this was fixed in place using white spirit.

P1320546_zpsstyu2xqh.jpg

P1320553_zpsca6m7ju6.jpg

Lastly some Ammo of Mig engine grime and Fresh Engine Oil was carefully applied in the appropriate places.

P1320558_zps68fbehkl.jpg

P1320553_zpsca6m7ju6.jpg
 

Share this post


Link to post
Share on other sites

That was the cockpit tub complete so attention was turned to the seats.  The WMIK seat for the rear gunner was made up then attacked with a scalpel to simulate cuts and general wear and tear.

P1320524_zpsois1z3iw.jpg

P1320527_zps2arn3tbj.jpg

The seat frames were painted using Mr. Paint's Soviet Interior.  Honestly, get this stuff, its by far the best paint on the planet.

P1320455_zpswrgfooc7.jpg

Metal bits were picked out using Ammo of Mig's new metallic acrylic.  This stuff is superb for brushing, it also sprays very well when thinned.

P1320486_zpsgmzq8ysv.jpg

To weather the vinyl, buff paint was dry brushed and strips of grey decal (from a 1:72 Phantom) were applied simulating gaffer tape repairs!

P1320536_zps6sbg5nbx.jpg

After a wash and decalling, the harnesses were added.  In this case the HGW He-111 set!

P1320539_zpsdgh00rsv.jpg

P1320528_zpsusfilypk.jpg

 

And that's the cockpit finished!

P1320561_zpspefmxo52.jpg

I'll post up how I got to this stage tomorrow, I don't want to bore you too much!

P1320622_zpsnbnj74y8.jpg

Share this post


Link to post
Share on other sites

If this is an approved scenario from the Air Warfare College, we're all in trouble!

 

Looks great (as ever...)

 

stresser (old avon IPMS chum).

Share this post


Link to post
Share on other sites

Great work Jamie...and thanks for the detailed tutorial - lots of good information shared from one of the "masters of effects."

 

Good stuff!

 

Rich

Share this post


Link to post
Share on other sites

Thanks guys, it means a lot.

 

Here is the next update chaps. First off, the cargo cabin.

 

The rear bulkhead was was detailed up, I didn't go made as it's going to be dark back there!

 

P1320382_zpsjyp13fqr.jpg

 

The floor plate was detailed with etched tread plate, plastic strip and HGW rivet decals. The basket is from the WMIK kit but the floor became the lid, a new floor was made with plastic card, the back blanked with photo etch mesh and various details added such as clasps, hinges etc.

 

P1320389_zpstuu3cigl.jpg

 

The bits were primed with Alclad black micro primer.

 

P1320424_zpsaebkyq4b.jpg

 

The various bits were painted and chipped as per the cockpit.

 

P1320437_zpslm641ixy.jpg

 

P1320440_zpsl3wmfobe.jpg

 

The tread plate didn't chip too well so it was enhanced by dry brushing.

 

P1320483_zpsdzqjjp2f.jpg

 

Rust was simulated by applying Ammo of Mig's Rust Streaking effects. When dry it was blended with a moist brush.

 

P1320568_zps6o9ul4hz.jpg

 

Ammo of Mig's Airfield Dust and Earth pigments were applied and fixed with white spirit.

 

P1320572_zpsduqwncj3.jpg

 

A thinned mix of Ammo of Mig Fresh Engine Oil, Engine Grime and Black pigment was applied to simulate old oil stains.

 

P1320577_zpsxld51cug.jpg

Share this post


Link to post
Share on other sites

I'm not usually into what-if's, but this is just brilliant.

 

Superb skills on display, real imagination, great weathering techniques, all done & photographed very well. And all done speedily.

 

I don't think I've ever learnt so much in such a short time - you should be charging for this!

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

×
×
  • Create New...