Loic Posted April 4, 2015 Share Posted April 4, 2015 Humm.... sorry. Hope you can fix this cause it's a great looking Spitfire Link to comment Share on other sites More sharing options...
monthebiff Posted April 4, 2015 Author Share Posted April 4, 2015 Thanks for the comments guys, Thinking about it Sparsanza and Ron have hit the nail on the head with the setting solution that I didn't clean up properly has attached the future but only reared its ugly head once the flory wash went on. After reflecting on it overnight I am thinking along the same lines as geedubelyer in doing a cover up job with weathering which is not what I really wanted to do as I wanted a pretty clean Spitty this time but needs must as I am not putting this on the shelf of doom as I have loved this build so far. Link to comment Share on other sites More sharing options...
Guest Peterpools Posted April 4, 2015 Share Posted April 4, 2015 Andy I have my fingers crossed all will work out. I've gone back to Glosscote and Flatcote, both being lacquers, dry rock hard and don't seem to be effected by washes or decal solutions. I have heard of this happening before and just leaving everything alone, over a day or so, the milky stains should disappear. Peter Link to comment Share on other sites More sharing options...
Mal_Belford Posted April 4, 2015 Share Posted April 4, 2015 Aoch....with them decals...since the build looks fantastic. That areas "White cloudy" if you take a cotton stick wet with water and apply it on them affected areas...does it dissapear...if so...there it is big chance that it will dissapear with a thin layer of clearcoat.... /Mal monthebiff 1 Link to comment Share on other sites More sharing options...
monthebiff Posted April 4, 2015 Author Share Posted April 4, 2015 Its been about 24 hours since I last did anything to her and decided I would start my weathering with some oil filters which seem to have helped out with the milky looking patches with most not all seeming to disappear as the oils dried out Compare with the shot I uploaded last night and things are looking much better today. This is how she is looking today, I have a few more idea's up my sleeve to cover the last 2 or 3 problem area's and sI will continue with the heavily weathered look on this one now. Thanks for looking in. Regards. Andy Uncarina, Girlscanplay2, Mal_Belford and 2 others 5 Link to comment Share on other sites More sharing options...
Iain Posted April 4, 2015 Share Posted April 4, 2015 Looking great Andy - really like it!! Iain Link to comment Share on other sites More sharing options...
Guest Peterpools Posted April 5, 2015 Share Posted April 5, 2015 Andy Glad the 'milky spots' are fading away. Keep 'em coming Peter Link to comment Share on other sites More sharing options...
DougN Posted April 5, 2015 Share Posted April 5, 2015 When I used to use Future, and got milky areas, they always disappeared under another coat of Future. Doug Link to comment Share on other sites More sharing options...
Henrique Posted April 6, 2015 Share Posted April 6, 2015 Hi Andy. Have you tried gloss coating these areas again? I had the same problem when letting Mr. Mark Softer sit just a few seconds over my Future (Pledge) coat. I let it dry and airbrushed another coat of Pledge over it and the milky stains were gone. Henrique Link to comment Share on other sites More sharing options...
monthebiff Posted April 7, 2015 Author Share Posted April 7, 2015 Thanks Henrique, DougN, As the milky patches are now all but gone I think I will continue with the weathering as I dont really want to use future on it or any other model again. As a gloss cote in future I'm toying with using Hannants Xtracolour Gloss as their Flat coat works like a dream, I have also seen/ heard Model Master Ultra Gloss straight from the rattle can gives pretty good results. Regards. Andy Link to comment Share on other sites More sharing options...
monthebiff Posted April 8, 2015 Author Share Posted April 8, 2015 Started with a few localized washes this evening followed by a little airbrush weathering. And the underside airbrush weathering started All was going well at this point, went in the other room for half an hour and had a drink and came back to find a major disaster on my hands.......it would seem the MIG wash I applied to the undercarriage has caused a reaction and melted the plastic as I found my Spit sitting on the deck less her undercarriage. . Hopefully I can drill and fit some brass rod to cure this one.........I hope............. Has anyone experienced problems like this, really gutted at this one as the finishing line is/was in site!! On a plus side my Quickboost exhausts arrived today. They are very nice and they will be fitted as I will be getting this Spit finished very soon as I'm not giving up on this one. Comments/criticism always welcome guys. Regards. Andy andromeda673, tomv87, Girlscanplay2 and 1 other 4 Link to comment Share on other sites More sharing options...
LSP_Kevin Posted April 8, 2015 Share Posted April 8, 2015 Wow, I don't think I've ever seen something like this happen simply due to paint or a wash. I'm assuming the Mig stuff is enamel, the petroleum base of which will easily soften plastic, but that's still an outrageous outcome after only 30 minutes! Any chance you could extract the remaining plastic stubs and use metal replacements? (That said, I'm not even sure if there are any metal replacements.) Kev Link to comment Share on other sites More sharing options...
monthebiff Posted April 8, 2015 Author Share Posted April 8, 2015 Yeah Kev your right on one both counts being its enamel and yes an outrageous outcome this evening, had a quick look at Hannants and they have a suitable metal set so will try and get the offending plastic out. Never had this happen before but always a first time, very soft plastic though!! Regards. Andy Link to comment Share on other sites More sharing options...
LSP_Ron Posted April 8, 2015 Share Posted April 8, 2015 I have never heard of this happening before. That's very very odd. Link to comment Share on other sites More sharing options...
monthebiff Posted April 9, 2015 Author Share Posted April 9, 2015 With a fresh mind I've had a good look at the offending plastic in question this evening Ron and both UC legs broke in the same place on a glue joint , I remember when I fitted the parts together I thought it a little poor on the engineering side at the time as the plastic is very soft and I suppose with the weight of the kit bearing down with a bit of enamel attacking the joint the outcome was inevitable. With a little patience this evening I have managed to extract the remaining UC leg from the wings and I have a set of metal Scale Model undercarriage legs on there way to from Hannants so all is definitely not lost. Regards. Andy Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now