Dragon Posted December 2, 2017 Share Posted December 2, 2017 (edited) I'm gonna color my world blue with Academy's F/A-18C dressed up as a VFC-12 Ambush adversary bird. I'll be using Fightertown Decals to do Ambush 06. In addition to the decals, I'll be using an aftermarket seat and of course the mandatory G-Factor brass landing gear. I'll be trying out the Bombshell Brew paints on this build, anxious to see how they perform. Supposed to be a rainy day in the PNW, so it'll be a good excuse to jump into this build. Mike Edited May 9, 2018 by Dragon BradG, LSP_Paul, Rick Griewski and 5 others 8 Link to comment Share on other sites More sharing options...
LSP_Paul Posted December 2, 2017 Share Posted December 2, 2017 Go Mike Go! Should be a fun one to watch. Paul Dragon 1 Link to comment Share on other sites More sharing options...
Youngtiger1 Posted December 2, 2017 Share Posted December 2, 2017 I'd be interesting to see how your Bombshell Brew paints perform. I had not heard of this outfits until now, so I'll see from your go around if I need to invest into any. So, follow along shell I. Dragon 1 Link to comment Share on other sites More sharing options...
Lud13 Posted December 2, 2017 Share Posted December 2, 2017 My top five Hornet Adversary schemes, looking for 1:48 decals for this one a long time Emilio, BradG, Alain Gadbois and 1 other 4 Link to comment Share on other sites More sharing options...
mark31 Posted December 2, 2017 Share Posted December 2, 2017 great paint sheme looking forward to that Have fun Mark Dragon 1 Link to comment Share on other sites More sharing options...
Dragon Posted December 4, 2017 Author Share Posted December 4, 2017 (edited) I decided to start this build off doing the centerline fuel tank. I wanted to do a quick and simple subassembly, so I could try out the Bombshell Brew paint. My paint of choice is Mr Color, and although I'm really happy with how it performs for me especially when doing freehand camo work, I'm always open to trying a new product. I really like the squeeze drop bottle Bombshell uses, makes paint dispensing easy, and the bottles have, what I'm assuming is, a ball bearing to aid mixing when shaking the bottle. The line has a wide range of colors for adversary aircraft which suits me with my current interest in adversary aircraft. After playing around with the paint consistency and air pressures for awhile, I found a combination that I thought performed the best for me. So, I tired it out on the fuel tank: I found the paint sprayed and covered nicely without any issues (the tank as pictured has a coat of Tamiya X-22). I still need to play around with the paint consistency and air pressures though as I wasn't able to get a nice tight demarcation line between colors that I like. More practice needed! A couple of other issues were exposed though. First, the paint colors don't match the decal colors. I've read it's difficult for decal printers to match the FS colors. I've had similar issues with low-viz decals. The second issue, the paint colors don't match the colors of the aircraft, see the pic posted by Lud13; their hue or shade just isn't the same as the colors on the aircraft. I understand that lighting conditions, camera settings, and one's computer screen settings can affect how the colors are seen, but to me, they aren't close. I'm going to get some AKAN paints and see how they look. Mike Edited December 4, 2017 by Dragon LSP_Paul, BradG, Starfighter and 1 other 4 Link to comment Share on other sites More sharing options...
Shawn M Posted December 4, 2017 Share Posted December 4, 2017 I took some detail shots of this bird a few years back, maybe they can help? https://www.flickr.com/photos/shawnmanny/albums/72157624943007610 Lud13, Dragon and BradG 3 Link to comment Share on other sites More sharing options...
Dragon Posted December 7, 2017 Author Share Posted December 7, 2017 (edited) Shawn - some great shots you have there. I'll definitely be using them for reference. Thanks! Maru - thanks for the encouragement. Hopefully, I can do it justice! A small and quick update. I ordered two AKAN paint sets from Linden Hill. One, is the Russian Deck Aviation set, and the other is the USSR Deck Aviation set. Fingers crossed the colors are a better match. I spent the evening painting the wheel wells white and prepared them for a wash. I'll let the paint and clear top coat dry a couple of days before applying the wash. I've also decided to do something I never do and that is to use a resin cockpit. Reading folks posts about their frustrations and the challenges getting resin pits to fit was something I didn't need to inflict on myself. However, I have been wanting to expand my modeling skills and test myself, so why not give this a try. Any advice is most welcomed! After painting the wheel wells, I started cleaning up some of the resin pieces that were the easiest to cleanup. I need to cut the pour block off the pit piece and the ejection seat. The seat comes with PE seatbelts, never used these either. Should be comical figure them out. Stay tuned for me probably getting frustrated and bailing to a seat with cast seatbelts! Mike Edited December 7, 2017 by Dragon LSP_Paul, mark31, Starfighter and 2 others 5 Link to comment Share on other sites More sharing options...
ClumsyDude Posted December 7, 2017 Share Posted December 7, 2017 That looks like the Aires cockpit if I'm not mistaken ... I used it on my current hornet build and was thrilled with it, I'm sure you will enjoy it too. Detail is incredible, and fitting it wasn't that tough. Good luck! Jim Dragon 1 Link to comment Share on other sites More sharing options...
Dragon Posted December 8, 2017 Author Share Posted December 8, 2017 (edited) Jim - yes, it is the Aires cockpit, and and I agree on the detail, very nice. I can see why folks include resin cockpits in their builds! Happy to hear the fit wasn't all that difficult. If I may ask, how much of the resin cockpit bottom did you have to remove? The kit cockpit has a notch in the bottom to allow the top of the front wheel well to attach to it. How did you address this with the resin cockpit? Thanks, Mike Edited December 8, 2017 by Dragon ClumsyDude 1 Link to comment Share on other sites More sharing options...
ClumsyDude Posted December 8, 2017 Share Posted December 8, 2017 Yeah, I had to sand the bottom pretty hard to get it to fit - it was quite papery and translucent by the time I got it where it needed to be, but I managed not to sand through it. As with most things in modelling, taking your time and checking regularly is the key. I started with my Dremel but finished off with hand sanding. Jim Dragon 1 Link to comment Share on other sites More sharing options...
Shawn M Posted December 8, 2017 Share Posted December 8, 2017 happy to help, its a lovely scheme Dragon 1 Link to comment Share on other sites More sharing options...
TorbenD Posted December 8, 2017 Share Posted December 8, 2017 Nice start Mike. What's life without setting yourself a little resin challenge - as Jim says, sand, fit, repeat (ad infinitum)... Torben Dragon 1 Link to comment Share on other sites More sharing options...
Dragon Posted December 12, 2017 Author Share Posted December 12, 2017 Nice start Mike. What's life without setting yourself a little resin challenge - as Jim says, sand, fit, repeat (ad infinitum)... Torben Torben - Yeah, I figured it was time to test myself with a resin challenge plus encouragement from my wife helped too! Well, I've decided to go all in with this resin challenge, so I picked up the Rhino Modelworks intakes and exhausts for this build. With all this resin, it's a good thing I have the G-Factor landing gear! The AKAH paints arrived today. I'll start spraying it later this week. Fingers crossed the colors are a closer match to the decal colors. Since I'll be playing with PE on this build, I figured I'd better get a proper tool to work it. So, I picked up a Hold and Fold. And here are my first pieces using the Hold and Fold tool: This tool is pretty slick! Definitely makes PE easier to work with. I also made some progress on the front wheel well: I still need to add a little wash to dirty it up a bit and give it some depth. That's it for now. Mike Lenny320, Starfighter, LSP_Paul and 3 others 6 Link to comment Share on other sites More sharing options...
LSP_Paul Posted December 12, 2017 Share Posted December 12, 2017 Wow Mike! Great Progress and cool new Toys! Good tools always make the job easier. Looking forward to seeing more soon! Paul Dragon 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now